Uxcell a16062200ux0500 Crane Pulley Block M15 Lifting Crane Swivel Hook single Pulley Block Hanging Wire Towing Wheel 10Pcs

Uxcell a16062200ux0500 Crane Pulley Block M15 Lifting Crane Swivel Hook single Pulley Block Hanging Wire Towing Wheel 10Pcs

List Price: $39.34
Price: $20.83
A crane pulley block is a kind of hoisting tool, also called a Sheave, is a mechanism composed of a wheel on an axle or shaft that may have a groove between two flanges around its circumference. A rope, cable, belt, or chain usually runs over the wheel and inside the groove, if present. Pulleys are used to change the direction of an applied force, transmit rotational motion, or realize a mechanical advantage in either a linear or rotational system of motion.Designed for use with rope or cord in indoor and outdoor applications, but only pulley here, rope is not included.
Furniture Lifter Mover Power Crane Kingkong Set Furniture Appliances

Furniture Lifter Mover Power Crane Kingkong Set Furniture Appliances

List Price: $69.98
Price: $61.99
rearrange furniture all by yourself. Use the lifter to lift the furniture enough to place the sliders underneath. Lifter gives you up to 330lb. Lift anything with just one hand without strain or injury. Made in JAPAN - How to Use : 1.Put the supporter under to furniture and lift it up. 2. Put Power Crane 4pcs each corner. 3. Move the Furniture easily.
Power Team (SPX) PE304 - Vanguard PE30 Electric 2-Speed Pump - Double-Acting, 1 hp, 1.25 gal Reservoir, 280.0 in³ Usable Capacity, 30 in³/min Flow at Max psi, 110/115 V, 50/60 Hz

Power Team (SPX) PE304 - Vanguard PE30 Electric 2-Speed Pump - Double-Acting, 1 hp, 1.25 gal Reservoir, 280.0 in³ Usable Capacity, 30 in³/min Flow at Max psi, 110/115 V, 50/60 Hz

Price: $11,720.99
  • Ideal for maintenance and construction applications
  • Deliver a powerful punch to operate single-acting or double-acting cylinders
  • Integral roll cage protects pump from abuse
  • 1 hp, single phase, permanent magnet motor
  • High performance to weight ratio
  • Starts under full load even when voltage is reduced to 50 % of nominal rating
  • CSA rated for intermittent duty
  • Remote controls and/or solenoid valves feature 24 volt controls
Specification:
  • pump type: PE30 Electric 2-Speed Pump
  • usable oil capacity: 280.0 in³
  • for use with: Double-Acting Cylinders
  • typical flow at max psi: 30 in³/min
  • power rating: 1 hp
  • typical flow at 10000 psi: 30 in³/min
  • voltage: 110/115 V
  • typical flow at 5000 psi: 38 in³/min
  • frequency: 50/60 Hz
  • typical flow at 1000 psi: 44 in³/min
  • amperage: 13.0 A
  • typical flow at 500 psi: 200 in³/min
  • motor phase: 1 ph
  • typical flow at 100 psi: 300 in³/min
  • valve part number: 9506
  • maximum pressure: 10000 psi
  • valve type: 4-Way, 3-Position (Tandem Center) Valve w/Posi-Check
  • sound level at idle/10000 psi: 87/82 dBA
  • valve type/function: 4-Way, 3-Position / Advance Hold Return
  • overall length: 10.000 in
Power Team (SPX) PA6-2 - PA6 Air-Driven Hydraulic Single Speed Pump - Single-Acting, 2.00 gal Reservoir, 454.0 in³ Usable Capacity, 10000 psi Max, 6 in³/min Flow at Max psi, High

Power Team (SPX) PA6-2 - PA6 Air-Driven Hydraulic Single Speed Pump - Single-Acting, 2.00 gal Reservoir, 454.0 in³ Usable Capacity, 10000 psi Max, 6 in³/min Flow at Max psi, High

Price: $3,039.70
  • Foot-operated air/oil pump-compact, lightweight & portable-single-speed pumps designed to drive single-acting cylinders
  • The power unit of choice for major manufacturers of auto body, frame straighteners and other equipment
  • Serviceable pump motor is not a "throw away", providing economical repair
  • Permanently vented reservoir cap
  • Internal relief valve protects circuit components, air inlet filter protects motor
Specification:
  • pump type: PA6 Air-Driven Hydraulic Single Speed Pump
  • typical flow at 10000 psi: 6 in³/min
  • for use with: Single-Acting Cylinders
  • outlet port size: 3/8 NPTF
  • reservoir capacity: 2.00 gal
  • reservoir material: High Density Polyethylene
  • reservoir capacity (cubic inches): 462.0 in³
  • sound level: 85 dBA
  • air pressure range: 40 to 120 psi
  • length: 11.50 in
  • usable oil capacity: 454.0 in³
  • width: 8.00 in
  • maximum pressure: 10000 psi
  • height: 10.25 in
  • typical flow at max psi: 6 in³/min
  • weight: 24.50 lb
  • typical flow at 100 psi: 465.000 in³/min
Power Team (SPX) PMA90U - PMA Series Air-Driven Multi-Fluid Pump - 13.6: 1, 1300 psi, 2.850 in³ Outlet per Cycle, 1.625 in Ram Dia, 915 in³/min Max Flow at 0 psi, 1 NPT In, 3/4

Power Team (SPX) PMA90U - PMA Series Air-Driven Multi-Fluid Pump - 13.6: 1, 1300 psi, 2.850 in³ Outlet per Cycle, 1.625 in Ram Dia, 915 in³/min Max Flow at 0 psi, 1 NPT In, 3/4

Price: $8,845.19
  • Provides infinitely variable capacity and discharge pressure
  • Suitable for continuous start/stop applications
  • Pumps oil, water, and other fluids
  • Stainless steel pump and check valves standard
  • Maintains pressure with minimal power consumption (non-load holding)
  • Usable in hazardous areas: per ATEX II, CAT. 2 GDcT5
  • Quiet operation
  • Can operate on gases other than air
  • Simple to install and maintain
  • Compact, rugged design
  • Only 15 psi air pressure required to start pump
  • Requires flooded inlet
  • Vertical mount
Specification:
  • ratio: 13.6:1
  • inlet port size: 1 NPT
  • outlet pressure: 1300 psi
  • outlet port size: 3/4 NPT
  • outlet per cycle: 2.850 in³
  • width: 9.06 in
  • ram diameter: 1.625 in
  • height: 8.27 in
  • max flow at zero pressure: 915 in³/min
Power Team (SPX) PMA130U - PMA Series Air-Driven Multi-Fluid Pump - 19: 1, 1880 psi, 2.040 in³ Outlet per Cycle, 1.375 in Ram Dia, 670 in³/min Max Flow at 0 psi, 3/4 NPT In, 1/2

Power Team (SPX) PMA130U - PMA Series Air-Driven Multi-Fluid Pump - 19: 1, 1880 psi, 2.040 in³ Outlet per Cycle, 1.375 in Ram Dia, 670 in³/min Max Flow at 0 psi, 3/4 NPT In, 1/2

Price: $8,866.49
  • Provides infinitely variable capacity and discharge pressure
  • Suitable for continuous start/stop applications
  • Pumps oil, water, and other fluids
  • Stainless steel pump and check valves standard
  • Maintains pressure with minimal power consumption (non-load holding)
  • Usable in hazardous areas: per ATEX II, CAT. 2 GDcT5
  • Quiet operation
  • Can operate on gases other than air
  • Simple to install and maintain
  • Compact, rugged design
  • Only 15 psi air pressure required to start pump
  • Requires flooded inlet
  • Vertical mount
Specification:
  • ratio: 19:1
  • inlet port size: 3/4 NPT
  • outlet pressure: 1880 psi
  • outlet port size: 1/2 NPT
  • outlet per cycle: 2.040 in³
  • width: 7.68 in
  • ram diameter: 1.375 in
  • height: 7.99 in
  • max flow at zero pressure: 670 in³/min
Power Team (SPX) PMA240B - PMA Series Air-Driven Multi-Fluid Pump - 36: 1, 3480 psi, 1.080 in³ Outlet per Cycle, 1.000 in Ram Dia, 354 in³/min Max Flow at 0 psi, 3/4 BSP In, 1/2

Power Team (SPX) PMA240B - PMA Series Air-Driven Multi-Fluid Pump - 36: 1, 3480 psi, 1.080 in³ Outlet per Cycle, 1.000 in Ram Dia, 354 in³/min Max Flow at 0 psi, 3/4 BSP In, 1/2

Price: $9,267.85
  • Provides infinitely variable capacity and discharge pressure
  • Suitable for continuous start/stop applications
  • Pumps oil, water, and other fluids
  • Stainless steel pump and check valves standard
  • Maintains pressure with minimal power consumption (non-load holding)
  • Usable in hazardous areas: per ATEX II, CAT. 2 GDcT5
  • Quiet operation
  • Can operate on gases other than air
  • Simple to install and maintain
  • Compact, rugged design
  • Only 15 psi air pressure required to start pump
  • Requires flooded inlet
  • Vertical mount
Specification:
  • ratio: 36:1
  • inlet port size: 3/4 BSP
  • outlet pressure: 3480 psi
  • outlet port size: 1/2 BSP
  • outlet per cycle: 1.080 in³
  • width: 7.68 in
  • ram diameter: 1.000 in
  • height: 7.99 in
  • max flow at zero pressure: 354 in³/min
Power Team (SPX) PA6D2 - PA6D Air-Driven Hydraulic Single Speed Pump - Double-Acting, 2.00 gal Reservoir, 454.0 in³ Usable Capacity, 10000 psi Max, 6 in³/min Flow at Max psi, Hig

Power Team (SPX) PA6D2 - PA6D Air-Driven Hydraulic Single Speed Pump - Double-Acting, 2.00 gal Reservoir, 454.0 in³ Usable Capacity, 10000 psi Max, 6 in³/min Flow at Max psi, Hig

Price: $4,876.19
  • Compact, lightweight and portable single -speed pump for driving double-acting cylinders
  • Internal relief valve protects circuit components, air inlet filter protects motor
  • Serviceable pump motor is not a "throw away", providing economical repair
  • Permanently vented reservoir cap
Specification:
  • pump type: PA6D Air-Driven Hydraulic Single Speed Pump
  • valve type/function: 3-Way/4-Way, 2-Position / Advance Return
  • for use with: Double-Acting Cylinders
  • valve function details: Position 1 - Oil is directed to "advance" side of cylinder, oil from "retract" side goes to reservoir; cylinder "holds" with pump shut off. Position 2 - Oil goes to "retract" side of cylinder; cylinder "holds" with pump shut off. When using as a 3-way valve for single-acting cylinders, port "A" or "B" is plugged.
  • reservoir capacity: 2.00 gal
  • outlet port size: 3/8 NPTF
  • reservoir capacity (cubic inches): 462.0 in³
  • reservoir material: High Density Polyethylene
  • air pressure range: 40 to 120 psi
  • sound level: 85 dBA
  • usable oil capacity: 454.0 in³
  • length: 11.31 in
  • maximum pressure: 10000 psi
  • width: 9.25 in
  • typical flow at max psi: 6 in³/min
  • height: 12.75 in
  • valve part number: 9504
  • weight: 28.60 lb
  • valve type: 3-Way/4-Way, 2-Position Manual Valve
Power Team (SPX) P300 - Two Speed Hand Pump for Single Acting Cylinders - 346.500 in³ Oil Capacity, 10000 psi Max Pressure, 0.160 in³ Max Volume per Stroke, 2-Way Valve

Power Team (SPX) P300 - Two Speed Hand Pump for Single Acting Cylinders - 346.500 in³ Oil Capacity, 10000 psi Max Pressure, 0.160 in³ Max Volume per Stroke, 2-Way Valve

Price: $2,739.74
  • Best suited for applications where there is little or no free travel
  • Rugged all metal construction for strength and durability that won't burn through in welding environments
  • Heavy-duty, formed metal handle provides less flex, and less operator fatigue than round or composite handles
  • Fill cap seal acts as safety valve to prevent over-pressurizing of reservoir
  • Relief valve inboard of check valve prevents loads from drifting down
  • Large valve knob gives added control for slowly metering loads down
Specification:
  • pump type: Two Speed
  • oil port size: 3/8 NPTF
  • use with ram type: Single Acting Cylinder
  • handle angle: 39°
  • oil capacity: 346.500 in³
  • handle effort: 140.00 lb
  • usable oil capacity: 310.000 in³
  • overall length: 22.625 in
  • maximum operating pressure: 10000 psi
  • overall width: 8.500 in
  • maximum pressure at low speed: 325 psi
  • overall height: 8.250 in
  • volume per stroke at high pressure: 0.160 in³
  • weight: 55.30 lb
  • volume per stroke at low pressure: 2.600 in³
  • valve type: 2-Way
Power Team (SPX) PA6AM - PA6 Air-Driven Hydraulic Single Speed Pump - Single-Acting, 0.45 gal Reservoir, 98.0 in³ Usable Capacity, 10000 psi Max, 6 in³/min Flow at Max psi, Metal

Power Team (SPX) PA6AM - PA6 Air-Driven Hydraulic Single Speed Pump - Single-Acting, 0.45 gal Reservoir, 98.0 in³ Usable Capacity, 10000 psi Max, 6 in³/min Flow at Max psi, Metal

Price: $4,292.59
  • Foot-operated air/oil pump-compact, lightweight & portable-single-speed pumps designed to drive single-acting cylinders
  • The power unit of choice for major manufacturers of auto body, frame straighteners and other equipment
  • Serviceable pump motor is not a "throw away", providing economical repair
  • Permanently vented reservoir cap
  • Internal relief valve protects circuit components, air inlet filter protects motor
Specification:
  • pump type: PA6 Air-Driven Hydraulic Single Speed Pump
  • valve type: Externally Adjustable Relief Valve
  • for use with: Single-Acting Cylinders
  • outlet port size: 3/8 NPTF
  • reservoir capacity: 0.45 gal
  • reservoir material: Metal
  • reservoir capacity (cubic inches): 105.0 in³
  • sound level: 85 dBA
  • air pressure range: 40 to 120 psi
  • length: 9.50 in
  • usable oil capacity: 98.0 in³
  • width: 5.88 in
  • maximum pressure: 10000 psi
  • height: 7.75 in
  • typical flow at max psi: 6 in³/min
  • weight: 17.00 lb
  • typical flow at 100 psi: 465.000 in³/min
  • typical flow at 10000 psi: 6 in³/min