Hard-to-Find Fastener 014973270049 Lead Wood Anchors, 10-14 x 1, Piece-100

Hard-to-Find Fastener 014973270049 Lead Wood Anchors, 10-14 x 1, Piece-100

List Price: $28.76
Price: $25.52
We stock a wide variety of fasteners ideal for many applications around the home, farm, business, automotives, and in industry. Most of our fasteners have a light Zinc plating over steel giving a more rust resistant finish. We also sell coated and stainless products for additional rust resistance. We stock many grades of fasteners ranging from low carbon steel on up to hardened, heat treated steel. Not all fasteners are applicable for all applications so be certain to test thoroughly and get the opinion of a licensed builder or certified building or structural engineer before relying on these fasteners for any situations where failure would result in damage to property or person.
L.H. Dottie 21 Anchor Tapered with Collar, No.6-8-10 by 7/8-Inch Length, Red, 100-Pack

L.H. Dottie 21 Anchor Tapered with Collar, No.6-8-10 by 7/8-Inch Length, Red, 100-Pack

List Price: $7.72
Price: $7.65
The L.H. Dottie 21 Anchor, Tapered with Collar, #6-8-10 by 7/8-inch length, fits 3/16-inch drill size. Made of durable plastic. Red color. This listing is for a standard package containing 100 units. Packed in Invincibox. Drill a hole into drywall, concrete, brick or block and insert anchor. Red.
CONFAST 1/4" Lag Shield Anchor Long (100 per box)

CONFAST 1/4" Lag Shield Anchor Long (100 per box)

List Price: $25.09
Price: $25.09
ApplicationsThe anchor is made from Zamac Alloy. This anchor is designed for use in Concrete, Block, and Brick.EnvironmentThe anchor is designed for use in a Wet environment.Hole Diameter/Bit DiameterThe anchor requires a 1/2" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Minimum EmbedmentThe minimum anchor embedment into the concrete is 1-1/2". Therefore, the anchor must be installed so that a minimum of 1-1/2" of the anchor is embedded into the concrete.Spacing between AnchorsEach anchor must be spaced a minimum distance of 5" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 2-1/2" from an unsupported edge of the concrete.
1/2" x 4-1/2", Powers Power-Stud+ SD2 Strength Design Wedge Expansion Anchors, Carbon Steel Zinc Plated Body w/ Stainless Steel Expansion Clip, 50/Bx

1/2" x 4-1/2", Powers Power-Stud+ SD2 Strength Design Wedge Expansion Anchors, Carbon Steel Zinc Plated Body w/ Stainless Steel Expansion Clip, 50/Bx

List Price: $60.42
Price: $60.42
The Power-Stud + Strength Design anchors are fully threaded, torque-controlled, wedge expansion anchors that are designed for consistent performance in cracked and uncracked concrete. Suitable base materials include normal-weight concrete, structural sand-lightweight concrete and concrete over metal deck. The SD2 is manufactured with a zinc plated carbon steel body and stainless steel expansion clip for premium performance. General Applications and Uses: • Structural connections - beam and column anchorage • Utility and safety-related attachments • Interior applications / low level corrosion environments • Tension zone applications - cable trays and strut, pipe supports, fire sprinklers • Seismic and wind loading • Medium to heavy duty purposes
CONFAST 5/8" (Inside/Screw 5/8" diameter) Double Expansion Anchor (15 per box)

CONFAST 5/8" (Inside/Screw 5/8" diameter) Double Expansion Anchor (15 per box)

List Price: $28.29
Price: $28.29
ApplicationsThe anchor is made from Zamac Alloy. This anchor is designed for use in Concrete, Block, and Brick.EnvironmentThe anchor is designed for use in a Moist environment.Hole Diameter/Bit DiameterThe anchor requires a 1" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Minimum EmbedmentThe minimum anchor embedment into the concrete is 2-5/8". Therefore, the anchor must be installed so that a minimum of 2-5/8" of the anchor is embedded into the concrete.Spacing between AnchorsEach anchor must be spaced a minimum distance of 10" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 5" from an unsupported edge of the concrete.
Prime-Line 9071190 Lag Shields, Short, 5/16 in. X 1-1/4 in., Zinc Alloy, 25-Pack

Prime-Line 9071190 Lag Shields, Short, 5/16 in. X 1-1/4 in., Zinc Alloy, 25-Pack

List Price: $12.82
Price: $12.68
Lag shield anchors allow lag screws to be installed into concrete and masonry walls. After drilling a hole into the material, lag shields should be tapped into place ribbed side first until flush with the surface. The lag screw can then be installed with a wrench or socket tool. The sides of the lag shield push out against the inside of the hole once the lag screw is installed, thereby locking it in place.
Prime-Line 9071684 Lag Shields, Long, 1/2 in. X 3 in., Zinc Alloy, 10-Pack

Prime-Line 9071684 Lag Shields, Long, 1/2 in. X 3 in., Zinc Alloy, 10-Pack

List Price: $22.49
Price: $17.81
Lag shield anchors allow lag screws to be installed into concrete and masonry walls. After drilling a hole into the material, lag shields should be tapped into place ribbed side first until flush with the surface. The lag screw can then be installed with a wrench or socket tool. The sides of the lag shield push out against the inside of the hole once the lag screw is installed, thereby locking it in place.
Hard-to-Find Fastener 014973281304 Lead Machine Screw Anchors, 1/2-13, Piece-50

Hard-to-Find Fastener 014973281304 Lead Machine Screw Anchors, 1/2-13, Piece-50

List Price: $79.31
Price: $79.31
We stock a wide variety of fasteners ideal for many applications around the home, farm, business, automotives, and in industry. Most of our fasteners have a light Zinc plating over steel giving a more rust resistant finish. We also sell coated and stainless products for additional rust resistance. We stock many grades of fasteners ranging from low carbon steel on up to hardened, heat treated steel. Not all fasteners are applicable for all applications so be certain to test thoroughly and get the opinion of a licensed builder or certified building or structural engineer before relying on these fasteners for any situations where failure would result in damage to property or person.
CONFAST 3/8" Lag Shield Anchor Long (50 per box)

CONFAST 3/8" Lag Shield Anchor Long (50 per box)

List Price: $27.29
Price: $27.29
ApplicationsThe anchor is made from Zamac Alloy. This anchor is designed for use in Concrete, Block, and Brick.EnvironmentThe anchor is designed for use in a Wet environment.Hole Diameter/Bit DiameterThe anchor requires a 5/8" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Minimum EmbedmentThe minimum anchor embedment into the concrete is 2-1/2". Therefore, the anchor must be installed so that a minimum of 2-1/2" of the anchor is embedded into the concrete.Spacing between AnchorsEach anchor must be spaced a minimum distance of 6-1/4" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 3-1/8" from an unsupported edge of the concrete.
Hard-to-Find Fastener 014973281274 Lead Machine Screw Anchors, 1/4-20, Piece-100

Hard-to-Find Fastener 014973281274 Lead Machine Screw Anchors, 1/4-20, Piece-100

List Price: $46.86
Price: $43.49
We stock a wide variety of fasteners ideal for many applications around the home, farm, business, automotives, and in industry. Most of our fasteners have a light Zinc plating over steel giving a more rust resistant finish. We also sell coated and stainless products for additional rust resistance. We stock many grades of fasteners ranging from low carbon steel on up to hardened, heat treated steel. Not all fasteners are applicable for all applications so be certain to test thoroughly and get the opinion of a licensed builder or certified building or structural engineer before relying on these fasteners for any situations where failure would result in damage to property or person.