Simpson Strong Tie STB2-50334 1/2-Inch by 3-3/4-Inch Bolt Wedge Anchor for Cracked and Uncracked Concrete, 25-Pack

Simpson Strong Tie STB2-50334 1/2-Inch by 3-3/4-Inch Bolt Wedge Anchor for Cracked and Uncracked Concrete, 25-Pack

List Price: $30.59
Price: $19.99
The Strong-Bolt is wedge anchor designed for optimum performance in both cracked and uncracked concrete: a requirement that the 2009 IBC places on post-installed anchors. The Strong-Bolt anchor is proven to offer increased reliability in the most adverse conditions, including cracked concrete under static and seismic loading. The proprietary tri-segmented clip has dual undercutting embossments on each segment which enable secondary or follow-up expansion if a crack forms and intersects the anchor location.
Strong Bolt STB2-50512 Wedge Anchor 1/2-Inch by 5-1/2-Inch, 25-Piece

Strong Bolt STB2-50512 Wedge Anchor 1/2-Inch by 5-1/2-Inch, 25-Piece

List Price: $25.87
Price: $25.87
The Strong-Bolt 2 wedge anchor is the next generation solution for cracked and uncracked concrete. Following rigorous testing according to ICC-ES acceptance criteria, the Strong-Bolt 2 anchor received classification as a Category 1 anchor, the highest attainable anchor category for performance in cracked concrete under static and seimic loading. Code listed by ICC-ES under the 2009 IBC requirements for post-installed anchors in cracked and uncracked concrete.
The Hillman Group 370984 Wedge Anchor, 3/8 X 3-Inch, 25-Pack

The Hillman Group 370984 Wedge Anchor, 3/8 X 3-Inch, 25-Pack

List Price: $23.99
Price: $16.48
The Power-Stud is a torque controlled, wedge expansion anchor that is designed for concrete applications. Has various DOT approvals including Cal Trans listing for "Stud Mechanical Expansion Anchors". It is building code approved and can also be used with treated lumber.
The Hillman Group 370986 Wedge Anchor, 3/8 X 5-Inch, 10-Pack

The Hillman Group 370986 Wedge Anchor, 3/8 X 5-Inch, 10-Pack

List Price: $16.20
Price: $9.85
The Power-Stud is a torque controlled, wedge expansion anchor that is designed for concrete applications. Has various DOT approvals including Cal Trans listing for "Stud Mechanical Expansion Anchors". It is building code approved and can also be used with treated lumber.
Strong Bolt STB2-50700 Wedge Anchor 1/2-Inch by 7-Inch, 25-Piece

Strong Bolt STB2-50700 Wedge Anchor 1/2-Inch by 7-Inch, 25-Piece

List Price: $31.24
Price: $27.78
The Strong-Bolt 2 wedge anchor is the next generation solution for cracked and uncracked concrete. Following rigorous testing according to ICC-ES acceptance criteria, the Strong-Bolt 2 anchor received classification as a Category 1 anchor, the highest attainable anchor category for performance in cracked concrete under static and seimic loading. Code listed by ICC-ES under the 2009 IBC requirements for post-installed anchors in cracked and uncracked concrete.
The Hillman Group 370980 Wedge Anchor, 1/4 X 2-1/4-Inch, 40-Pack

The Hillman Group 370980 Wedge Anchor, 1/4 X 2-1/4-Inch, 40-Pack

List Price: $21.42
Price: $17.73
The Power-Stud is a torque controlled, wedge expansion anchor that is designed for concrete applications. Has various DOT approvals including Cal Trans listing for "Stud Mechanical Expansion Anchors". It is building code approved and can also be used with treated lumber.
CONFAST 1/2 x 5-1/2 Hot-Dipped Galvanized Wedge Anchor (Box of 25)

CONFAST 1/2 x 5-1/2 Hot-Dipped Galvanized Wedge Anchor (Box of 25)

List Price: $30.99
Price: $30.99
ApplicationsThe anchor is made from Carbon Steel, and is Hot-Dipped Galvanized. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. EnvironmentThe anchor is designed for use in a Damp environment.Hole Diameter/Bit DiameterThe anchor requires a 1/2" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Diameter of Anchor The diameter of the anchor is 1/2".Length Anchor The length of the anchor is 5-1/2"Thread LengthThe length of the threads on the anchor is 4" in length.Minimum EmbedmentThe minimum anchor embedment into the concrete is 2-1/4". Therefore, the anchor must be installed so that a minimum of 2-1/4" of the anchor is embedded into the concrete.Maximum Fixture ThicknessThe maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 2-3/4". This will ensure that the minimum embedment of 2-1/4" will be met.Fixture Hole DiameterThe hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/2" diameter anchor requires the hole in the fixture to be 5/8".Torque ValueTo be set properly in the concrete, the anchor must be torqued to between 50 - 60 ft./lbs.Spacing between AnchorsEach anchor must be spaced a minimum distance of 5" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 2-1/2" from an unsupported edge of the concrete.
CONFAST 3/4 x 5-1/2 Wedge Anchor Zinc Plated (Box of 20)

CONFAST 3/4 x 5-1/2 Wedge Anchor Zinc Plated (Box of 20)

List Price: $30.99
Price: $30.99
ApplicationsThe anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. EnvironmentThe anchor is designed for use in a Dry environment.Hole Diameter/Bit DiameterThe anchor requires a 3/4" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Diameter of Anchor The diameter of the anchor is 3/4".Length Anchor The length of the anchor is 5-1/2"Thread LengthThe length of the threads on the anchor is 3-1/4" in length.Minimum EmbedmentThe minimum anchor embedment into the concrete is 3-1/4". Therefore, the anchor must be installed so that a minimum of 3-1/4" of the anchor is embedded into the concrete.Maximum Fixture ThicknessThe maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-1/2". This will ensure that the minimum embedment of 3-1/4" will be met.Fixture Hole DiameterThe hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/4" diameter anchor requires the hole in the fixture to be 1".Torque ValueTo be set properly in the concrete, the anchor must be torqued to between 150 - 175 ft./lbs.Spacing between AnchorsEach anchor must be spaced a minimum distance of 7-1/2" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 3-3/4" from an unsupported edge of the concrete.
CONFAST 1/2" x 7" Hot-Dipped Galvanized Wedge Anchor (Box of 25)

CONFAST 1/2" x 7" Hot-Dipped Galvanized Wedge Anchor (Box of 25)

List Price: $39.99
Price: $39.99
ApplicationsThe anchor is made from Carbon Steel, and is Hot-Dipped Galvanized. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. EnvironmentThe anchor is designed for use in a Damp environment.Hole Diameter/Bit DiameterThe anchor requires a 1/2" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Diameter of Anchor The diameter of the anchor is 1/2".Length Anchor The length of the anchor is 7"Thread LengthThe length of the threads on the anchor is 4" in length.Minimum EmbedmentThe minimum anchor embedment into the concrete is 2-1/4". Therefore, the anchor must be installed so that a minimum of 2-1/4" of the anchor is embedded into the concrete.Maximum Fixture ThicknessThe maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 4-1/4". This will ensure that the minimum embedment of 2-1/4" will be met.Fixture Hole DiameterThe hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/2" diameter anchor requires the hole in the fixture to be 5/8".Torque ValueTo be set properly in the concrete, the anchor must be torqued to between 50 - 60 ft./lbs.Spacing between AnchorsEach anchor must be spaced a minimum distance of 5" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 2-1/2" from an unsupported edge of the concrete.
CONFAST 1/2" x 4-1/4" Hot-Dipped Galvanized Wedge Anchor (Box of 25)

CONFAST 1/2" x 4-1/4" Hot-Dipped Galvanized Wedge Anchor (Box of 25)

List Price: $22.69
Price: $22.69
ApplicationsThe anchor is made from Carbon Steel, and is Hot-Dipped Galvanized. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. EnvironmentThe anchor is designed for use in a Damp environment.Hole Diameter/Bit DiameterThe anchor requires a 1/2" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Diameter of Anchor The diameter of the anchor is 1/2".Length Anchor The length of the anchor is 4-1/4"Thread LengthThe length of the threads on the anchor is 2-3/4" in length.Minimum EmbedmentThe minimum anchor embedment into the concrete is 2-1/4". Therefore, the anchor must be installed so that a minimum of 2-1/4" of the anchor is embedded into the concrete.Maximum Fixture ThicknessThe maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-1/2". This will ensure that the minimum embedment of 2-1/4" will be met.Fixture Hole DiameterThe hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/2" diameter anchor requires the hole in the fixture to be 5/8".Torque ValueTo be set properly in the concrete, the anchor must be torqued to between 50 - 60 ft./lbs.Spacing between AnchorsEach anchor must be spaced a minimum distance of 5" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 2-1/2" from an unsupported edge of the concrete.